Upwork CISCO NETWORKING TEST 2016

Hello Freelancer, Welcome to allupworktestanswers.com Here to get the CISCO NETWORKING TEST of Latest version 2016. We are ready here to provide your desire upwork test answer. We already tested all exam test information Available include on here. So Dear, Why Late? Read the below full exam test and get more information from our website.


1. Which of the following routing protocols support VLSM?
Answers:
  1. RIP v1
  2. RIP v2
  3. IGRP
  4. EIGRP
  5. OSPF
2. Which of the following devices can be connected using a Rollover cable?
Answers:
  1. Router Ethernet Port to Router Ethernet Port
  2. Switch Console Port to PC COM Port
  3. Switch Ethernet Port to Switch Ethernet Port
  4. Router Ethernet Port to Switch Ethernet Port
  5. Router Console Port to PC COM Port
3. Which of the following ranges are reserved as private addresses?
Answers:
  1. 192.168.0.0 – 192.255.255.255
  2. 172.16.0.0 – 172.255.255.255
  3. 10.0.0.0 – 10.255.255.255
  4. 172.16.0.0 – 172.31.255.255
4. Which two factors are used by default for calculation of metric by EIGRP?
Answers:
  1. Bandwidth
  2. Hop Count
  3. Reliability
  4. Load
  5. Delay
5. Which of the following routing protocols are not classless routing protocols?
Answers:
  1. EIGRP
  2. OSPF
  3. IGRP
  4. RIP v1
6. Which of the following Protocols work on Application Layerr of OSI model?
Answers:
  1. HTTP
  2. FTP
  3. IP
  4. UDP
7. Which two statements are true about CHAP authentication method?
Answers:
  1. It is more secure than PAP
  2. It is supported by HDLC
  3. It is less secure than PAP
  4. It sends authentication messages periodically during the connection
8. Which of the following routing protocols are distance vector routing protocols?
Answers:
  1. OSPF
  2. RIP
  3. EIGRP
  4. IGRP
9. Which command is used to encrypt all the passwords of a router?
Answers:
  1. enable password-encryption
  2. service password-encryption
  3. encrypt passwords
  4. enable encrypt-password
10. Which subnet mask will you use to fulfill the requirements of all the departments if you are using a class C network?
Answers:
  1. 255.255.255.0
  2. 255.255.255.252
  3. 255.255.255.224
  4. 255.255.255.192
  5. 255.255.255.128
11. Which of the following addresses is reserved for loopback tests?
Answers:
  1. 10.0.0.1
  2. 172.16.0.1
  3. 192.168.0.1
  4. 127.0.0.1
12. Which is the command to view all available commands in the mode you are working in?
Answers:
  1. show all
  2. ?
  3. help
  4. help commands
13. Which command is used to view IP routing table?
Answers:
  1. show ip table
  2. show route
  3. show ip route
  4. show routing table
14. Which command is used to disable domain lookup?
Answers:
  1. no ip domain-lookup
  2. disable domain-lookup
  3. no domain-lookup
  4. None of the above
15. Which of the following routing protocols are Cisco proprietary?
Answers:
  1. IGRP
  2. EIGRP
  3. OSPF
  4. RIP
16. Which command is used to configure the configuration-register of a router?
Answers:
  1. Router(config)# config-register 0x2102
  2. Router# config-register 0x2102
  3. Router(config-line)# config-register 0x2102
  4. Router(config-router)# config-register 0x2102
17. Which of the following commands will prevent telnet access from all users on subnet 172.16.16.0 with subnet mask 255.255.240.0 to any destination?
Answers:
  1. access-list 115 deny tcp 172.16.16.0 255.255.240.0 any eq 23
  2. access-list 115 deny tcp 172.16.16.0 0.0.16.255 any eq 23
  3. access-list 115 deny tcp 172.16.16.0 0.0.15.255 any eq 21
  4. access-list 115 deny tcp 172.16.16.0 0.0.15.255 any eq 23
18. What is the default value of flush timers in IGRP?
Answers:
  1. 630 seconds
  2. 90 seconds
  3. 270 seconds
  4. None of the above
19. If UDP receives datagrams that are not in sequence, what will it do?
Answers:
  1. It will drop datagrams that are not in sequence
  2. It will arrange them in sequence using sequence numbers
  3. It will request source host to resend datagrams
  4. None of the above
20. Which of the following commands will allow a single source address 172.16.0.5 to telnet a single destination address 192.168.10.2?
Answers:
  1. access-list 150 permit tcp host 172.16.0.5 host 192.168.10.2 eq 23
  2. access-list 150 deny tcp host 172.16.0.5 host 192.168.10.2 eq 23
  3. access-list 150 permit tcp any any
  4. access-list 150 permit ip any any eq 23
21. Which command will disable CDP on a router?
Answers:
  1. no cdp run
  2. disable cdp
  3. no cdp enable
  4. no cdp route
22. What is the default number of commands that a router can show if you execute ‘show history’ command?
Answers:
  1. 15
  2. 10
  3. 20
  4. 256
23. Which is the default mode of operation in a VTP domain for all catalyst switches?
Answers:
  1. Client
  2. Server
  3. Transparent
  4. None of the above
24. Which command will you use to enable default routing on a router?
Answers:
  1. outer(config)# ip route 255.255.255.255 0.0.0.0 172.16.0.1
  2. outer(config)# ip route default 0.0.0.0 0.0.0.0 172.16.0.1
  3. outer(config)# ip route 0.0.0.0 0.0.0.0 172.16.0.1
  4. outer# ip route 0.0.0.0 0.0.0.0 172.16.0.1
25. How many Broadcast Domains are there if two switches are connected to each other using a trunk link?
Answers:
  1. 2
  2. 1
  3. 4
  4. None
26. How many bits of a MAC address are used by OUI portion?
Answers:
  1. 32 bits
  2. 48 bits
  3. 24 bits
  4. 16 bits
27. Which area must be present to connect two different areas in an OSPF network?
Answers:
  1. Area 0
  2. Area 51
  3. Area 1
  4. Area 16
28. What is the maximum number of valid IP addresses in a class B network?
Answers:
  1. 65536
  2. 65534
  3. 256
  4. 254
29. You made some changes in your router’s configuration and executed the following command:
Router# copy run start
When you restarted your router it went into the Setup mode. What is the problem?
Answers:
  1. The command ‘copy run start’ is incorrect
  2. The NVRAM is corrupt
  3. The value of configuration register is set to 0x2142
  4. Nothing is wrong, you have to configure the router every time it restarts
30. Routing protocols use a method to advertise many networks as one network to other routers. What is that method called?
Answers:
  1. Supernetting
  2. Summarization
  3. Subnetting
  4. None of the above
31. What is the speed of a T1 line?
Answers:
  1. 128 kbps
  2. 144 kbps
  3. 2.048 Mbps
  4. 1.544 Mbps
32. What is the hop count limit for OSPF?
Answers:
  1. 15
  2. 255
  3. 256
  4. None
33. What is the main purpose of creating VLANs?
Answers:
  1. They create single collision domain
  2. They provide fast speed to the LANs
  3. They break up the broadcast domain
  4. None of the above
34. What is the maximum speed supported by a standard ISDN BRI?
Answers:
  1. 64 kbps
  2. 128 kbps
  3. 256 kbps
  4. 1.544 mbps
35. What will be the command for standard access control list to deny a single source address 10.15.12.2?
Answers:
  1. access-list 50 deny 10.0.0.0 255.255.255.0
  2. access-list 50 deny 10.15.12.2 0.255.255.255
  3. access-list 50 deny host 10.15.12.2
  4. access-list 50 deny 10.15.12.2 255.255.255.255
36. In which of the following networks, are DR and BDR elected in OSPF?
Answers:
  1. Broadcast multi-access
  2. Point-to-point
  3. Nonbroadcast multi-access
  4. Point-to-multipoint
37. Which of the following devices can be connected using a straight cable?
Answers:
  1. Hub & Switch
  2. Router & PC
  3. PC & PC
  4. Router & Switch
38. If a router has been configured for static routing, IGRP, OSPF, EIGRP and RIP with their default values, which routing will the router use to send data?
Answers:
  1. RIP
  2. OSPF
  3. IGRP
  4. EIGRP
  5. Static Routing
39. What is the command to configure PPP encapsulation on serial 0?
Answers:
  1. Router(config)# configure encapsulation ppp
  2. Router(config)# encapsulation ppp
  3. Router(config-if)# encapsulation ppp
  4. Router# encapsulation ppp serial 0
40. On which layer of the OSI model do TCP & UDP work?
Answers:
  1. Transport Layer
  2. Session Layer
  3. Presentation Layer
  4. Network Layer
41. What should be the value of configuration register in a router to boot IOS image stored in ROM?
Answers:
  1. 0x2102
  2. 0x2101
  3. 0x2142
  4. 0x101
42. Refer to the diagram.
Host A is not able to communicate with Host B. However, Router A can communicate with Host B. What could bethe problem?
Answers:
  1. Host A’s IP address is incorrect
  2. Router A’s Ethernet 0 IP address is incorrect
  3. Host B’s IP address is incorrect
  4. No routing is configured among the routers
43. Which layer of OSI model encapsulates packets into frames?
Answers:
  1. Transport Layer
  2. Data Link Layer
  3. Network Layer
  4. Physical Layer
44. Which of the following are examples of the Data Link Layerr?
Answers:
  1. Token Ring
  2. IP
  3. Ethernet
  4. MAC
  5. IPX
45. If you set bandwidth of 64 kbps on an interface, what will be it’s cost in OSPF?
Answers:
  1. 256
  2. 1563
  3. 1024
  4. 2096
46. What is the command to configure q933a as frame relay LMI type?
Answers:
  1. Router(config)# frame-relay lmi-type q933a
  2. Router# lmi-type q933a
  3. Router(config-if)# frame-relay lmi-type q933a
  4. Router(config-if)# lmi-type q933a
47. What is the full form of CSMA/CD?
Answers:
  1. Code Sense, Multiple Access with Collision Detection
  2. Carrier Sense, Multiple Access with Code Division
  3. Collision Sense, Multiple Access with Carrier Detection
  4. Carrier Sense, Multiple Access with Collision Detection
48. Which of the following are frame relay LMI types?
Answers:
  1. DLCI
  2. Cisco
  3. IEEE 802.1Q
  4. Q933A
49. If interface Ethernet 0 is showing that it is administratively down, what will you do to turn it on?
Answers:
  1. Change the cable connected with Ethernet 0
  2. Restart the route
  3. Execute ‘no shutdown’ command
  4. Execute ‘clock rate ‘ command
50. In which of the following modes does a switch not participate in VTP domain, but still forwards VTP advertisements by trunk links?
Answers:
  1. Server
  2. Domain
  3. Client
  4. Transparent
51. Different routing protocols use different methods to calculate the distance to a network. What is that method called?
Answers:
  1. Administrative Distance
  2. Metric
  3. Routing Table
  4. None of the above
52. What is the maximum number of subnets (usable) that you can create in a class B network?
Answers:
  1. 16384
  2. 32768
  3. 65536
  4. Infinite
53. What is the speed of ISDN PRI service with 30B +1D channel?
Answers:
  1. 2.048 Mbps
  2. 1.544 Mbps
  3. 144 Kbps
  4. 128 Kbps
54. What is the binary value of hex 9F?
Answers:
  1. 10011111
  2. 10111000
  3. 11110001
  4. 10001111
55. Which of the following switches support both ISL and 802.1Q encapsulation methods?
Answers:
  1. 1900
  2. 2950
  3. 3550
  4. All of the above
56. Which command will you use to view sending and receiving of RIP update packets that normally run in the background ?
Answers:
  1. Router(config-router)# debug ip rip
  2. Router# debug rip packets
  3. Router# debug ip rip
  4. Router(config)# show rip packets
57. What is the default value of bridge priority on Cisco switches?
Answers:
  1. 65536
  2. 16384
  3. 32768
  4. 256
58. Which command will you execute to see whether the cable attached with your router’s Serial 0 is DCE or DTE?
Answers:
  1. show controllers serial 0
  2. show interface serial 0
  3. show ip interface serial 0
  4. show interface brief serial 0
59. Which of the following commands will you use to enable RIP version 2 on your router?
Answers:
  1. Router(config)# version 2
  2. Router(config-router)# version 2
  3. Router(config-if)# version 2
  4. Router# rip version 2
60. Which of the following statements is true regarding VLAN 1?
Answers:
  1. It is a default VLAN
  2. You cannot delete VLAN 1
  3. You cannot rename VLAN 1
  4. All of the above
61. At which layer of OSI Model does a router work?
Answers:
  1. Presentation Layer
  2. Transport Layer
  3. Network Layer
  4. Datalink Layer
  5. Application Layer
  6. Physical Layer
  7. Session Layer
62. Which information is exchanged by Cisco devices on which CDP is running?
Answers:
  1. Routing Tables
  2. Platform
  3. Traffic Data
  4. Capabilities List
  5. Username & Password
63. Which of the following switching methods forward the frame after reading the destination MAC address only?
Answers:
  1. Fast forward
  2. Cut-through
  3. Fragment free
  4. Store and forward
64. You executed the following command on your router:
Router(config)# router ospf 15
Which command will you execute next to complete OSPF configuration on your router?
Answers:
  1. Router(config-router)# network 172.16.0.0 255.255.0.0 area 5
  2. Router(config)# network 172.16.0.0 0.0.255.255 area 5
  3. Router(config-router)# network 172.16.0.0 0.0.255.255 area 5
  4. Router(config# ip route ospf 172.16.0.0 255.255.0.0 area 5
65. Which of the following devices is used to connect a non ISDN device with an ISDN network?
Answers:
  1. NT1
  2. TE2
  3. TA
  4. TE1
66. Which of the following services can be used to set up a database of MAC addresses that can be used for dynamic addressing of VLANs?
Answers:
  1. Static VLAN
  2. VMPS
  3. STP
  4. VTP
67. Which command will you use to configure IP address on an interface?
Answers:
  1. Router(config-if)# ip 192.168.1.1 255.255.255.0
  2. Router(config-if)# ip address 192.168.1.1
  3. Router(config-if)# ip address 192.168.1.1/24
  4. Router(config-if)# ip address 192.168.1.1 255.255.255.0
  5. Router(config-if)# ip address 192.168.1.1 subnet 255.255.255.0
68. Which of the following provides routing protocol support for IPX, Appletalk and IP networks simultaneously?
Answers:
  1. RIP v2
  2. OSPF
  3. IGRP
  4. EIGRP
69. What is the subnetwork to which IP address 10.70.50.255/18 belongs?
Answers:
  1. 10.70.10.0
  2. 10.70.50.0
  3. 10.70.32.0
  4. 10.70.0.0
  5. 10.0.0.0
70. What is the maximum number of paths supported by IGRP for load balancing?
Answers:
  1. Fou
  2. Six
  3. Twelve
  4. Infinite
71. What is the Administrative Distance (AD) of OSPF?
Answers:
  1. 1
  2. 120
  3. 110
  4. 90
72. What will happen if you declare an interface as passive interface in IGRP routing protocol?
Answers:
  1. The router will stop sending and receiving any dynamic updates
  2. The router will stop sending any dynamic updates but can still receive updates
  3. The interface will stop receiving any dynamic updates
  4. The interface will stop sending any dynamic updates but can still receive updates
73. What is the binary value of 157?
Answers:
  1. 11000111
  2. 10111001
  3. 11100011
  4. 10011101
74. What is the OUI portion of MAC address B4-3F-95-5F-1D-09 in binary?
Answers:
  1. 10110100-00111111-10010101
  2. 11100110-11001001-01110011
  3. 11000011-10000111-11110001
  4. 00111100-10010001-10111001
75. Which one of the following addresses can be used as a host address for the subnet 192.168.50.16/28?
Answers:
  1. 192.168.50.32
  2. 192.168.50.16
  3. 192.168.50.64
  4. 192.168.50.30
76. Which of the following subnet masks should you use on Router A and Router B serial links so that there is minimum wastage of IP addresses?
Answers:
  1. 255.255.255.255
  2. 255.255.0.0
  3. 255.255.255.0
  4. 255.255.255.252
  5. 255.255.255.254
77. Which of the following are stored in RAM?
Answers:
  1. Startup-config
  2. Running-config
  3. Routing Table
  4. All of the above
78. Which of the following commands show Cisco IOS image file name?
Answers:
  1. show startup
  2. show running
  3. show version
  4. show history
79. Which of the following statements are true for inter VLAN communication?
Answers:
  1. A router that supports inter VLAN communication is required
  2. The router must support the same encapsulation method as supported by the switch
  3. If the router has only one Ethernet interface, sub-interfaces must be configured
  4. All of the above
80. Which type of NAT uses different ports to map multiple IP addresses to a single global IP address?
Answers:
  1. Dynamic NAT
  2. NAT with overloading
  3. Static NAT
  4. All of the above
81. What do you understand from the following commands:
access-list 110 deny tcp 192.168.10.0 0.0.0.255 any eq 21
access-list 110 permit ip any any
Answers:
  1. This access-list denies any Telnet traffic from network 192.168.10.0 255.255.255.0
  2. This access-list allows any IP traffic from any source to any destination
  3. This access-list denies any FTP traffic from network 192.168.10.0 255.255.255.0
  4. This access-list denies any FTP traffic to network 192.168.10.0 255.255.255.0
82. State whether True or False:
You can only create that number of VLANs which are equivalent to the number of ports on a switch.
Answers:
  1. True
  2. False
83. Which of the following VLANs is recommended by Cisco to be used as an administrative VLAN?
Answers:
  1. VLAN 0
  2. VLAN 1
  3. VLAN 1024
  4. VLAN 16
84. How many bearer(B) and data(D) channel/s are there in a standard ISDN BRI service?
Answers:
  1. 2B + 1D Channel
  2. 23B + 1D Channel
  3. 24B + 2D Channels
  4. 16B + 1D Channel
85. What is the command to show Frame relay map table?
Answers:
  1. Router(config)# show frame-relay map
  2. Router# show frame-relay
  3. Router(config-router)# show frame-relay table
  4. Router# show frame-relay map
86. State whether True or False:
You have two routers connected with point-to-point links using different encapsulation methods. They will be able to communicate with each other.
Answers:
  1. True
  2. False
87. Which of the following things are stored in RAM?
Answers:
  1. ARP Cache
  2. Running configuration
  3. Routing tables
  4. All of the above
88. Which statement is true about RID (Router ID) in OSPF?
Answers:
  1. It is always the highest IP address of active interfaces
  2. It is the highest IP address of all configured loopback interfaces
  3. It is locally significant
  4. It is only used for election of DR
89. Which encapsulation method will you choose if you want to connect a Cisco router and a non Cisco router with a serial connection?
Answers:
  1. HDLC
  2. PPP
  3. LAPD
  4. LAPB
90. Which key combination is used to interrupt the boot sequence of a router?
Answers:
  1. Esc + Ctrl
  2. Ctrl + Z
  3. Ctrl + Break
  4. Alt + Ctrl + Del
91. Which command is used to view the list of all active connections made to the console and VTY ports of your router?
Answers:
  1. show session
  2. show connections
  3. show lines
  4. show users
92. Which protocol uses port number 23?
Answers:
  1. FTP
  2. SMTP
  3. Telnet
  4. HTTP
93. What is the decimal equivalent of binary 11001110?
Answers:
  1. 207
  2. 250
  3. 206
  4. 192
94. Which of the following cables is not prone to electrical interferences?
Answers:
  1. Shielded Twisted Pair (STP)
  2. Unshielded Twisted Pair (UTP)
  3. Fiber Optic
  4. Copper wire
  5. Coaxial
95. How many access control lists can be applied on an interface?
Answers:
  1. One access control list in each direction for each protocol
  2. Two access control lists in each direction
  3. Unlimited
  4. Access control list cannot be applied on an interface
96. What is the command for copying a router’s IOS to a TFTP server?
Answers:
  1. copy ios tftp
  2. copy start tftp
  3. copy flash tftp
  4. copy flash-config tftp
97. You are not able to create a new VLAN and cannot delete or change existing VLANs on a switch. What could be the problem?
Answers:
  1. Trunk link is not configured properly
  2. The switch is in VTP Transparent mode
  3. The switch is in VTP Client mode
  4. None of the above
98. What is the network ID of IP address 172.16.40.0/20?
Answers:
  1. 172.16.16.0
  2. 172.16.36.0
  3. 172.16.32.0
  4. 172.16.0.0
99. What is the full form of ISDN?
Answers:
  1. International Subscriber Digital Network
  2. International Services Digital Network
  3. Internet Services Digital Network
  4. Integrated Services Digital Network
Finally no more words require about the CISCO NETWORKING TEST  information in this session of this content. If you are require knowing more, Please ask to us via our contact us form or comment box. Please make sure that, you don’t send Personal information via the Comment box.  Thank you very mutch for being with us.

0 comments: